Applications

back to overview

Automotive industry

Reliable quality assurance of functional components

Micro and nano structured 3D functional surfaces reduce fuel consumption, make cars more environmentally compatible and reduce wear. Key components in the fuel feed supply and drive technology have to be precisely manufactured and inspected. Stable process control in production calls for fast measurement technology in the production environment. For this reason, leading automobile manufacturers are increasingly turning to NanoFocus technology.

Examples of application

The non-contact measurement technology of NanoFocus precisely determines the quality of surface structures of cylinder running surfaces, camshafts, connecting rods, coatings or sheet metal in the laboratory or during production.


Coated surfaces (Appearance)

The appearance of varnished and unvarnished sheet metal is determined by structure and waviness on a microscopic level. With µsurf mobile samples of previously defined areas of the cary body can be measured at various steps of the production process.  The amplitudes of the single wavelenghts bands are protocolled. The influence of the material and the manufacturing conditions can be evaluated comprehensively at the hands of this data. The measurement results in one zone profile can be compared to set-values of a car model.
Read more about appearance measurements.

Products:  µsurf mobile, µsurf expert, µsurf explorer, µsurf custom, µsoft analysis


Gaskets

Automated optical inspection system on the basis of the µsprint-technology determine the three-dimensional characteristics of sealing sheets only 60 µm thick, which are applied to their substrates using screen printing. µsprint takes just a fraction of the time required by tactile profilometers to perform this task. In addition, the system scans the surface structures in the low µm range without contact, and much more accurately, too. Within only a few minutes, it is possible not only to measure the properties of the seals over the surface of the entire panel, but also to measure various data points relating to the surface composition.

Products: µsprint hp-hsi, µsprint sensor, µsoft analysis


Injection systems

During production of piezo-common rail (PCR) injection systems, quality assurance is performed with the ultra-fast µsprint technology. Welded metal membranes are examined for evenness, surface defects and welding spatter - fully automated and with cycle times of six seconds. The samples are handled with the help of a SPS-controlled robot. The software µsoft automation enables measurement processes on the basis of recipes. The measurement results are stored in an SQL-data base.

Products: µsprint hp-hsi, µsprint sensor, µsoft analysis


Sheet metal

The oil pockets rolled into sheet metal serve to absorb oil and improve its shaping properties. Practically relevant evaluation tools are available for the analysis of these functionally important 3D structural elements. Alongside DIN EN ISO roughness evaluations, the microvolume of the enclosed proportion of the surface can be calculated and evaluated. The stitching function is used to expand the measurement fields to several millimeters.

Products: µsurf expert, µsurf explorer, µsurf mobile, µsurf custom, µsoft analysis


Laser welded seams

The 3D line-sensors of the µsprint technology inspects the quality of laser welded seams for pores, bubbles and vats. Additionally, the completeness and coherence of the seams can be examined fully automated. If the software µsoft automation declares a sample as not ok, welding and measurement can be repeated. In this way, the reject rate can be reduced signigicantly.

Products: µsprint custom, µsprint sensor, µsoft analysis


Cam rings

Burned in laser pads on the inside of cam rings are inspected for structure depth and roughness. In the laser structuring process carves and chunking can be measured and evaluated during production. NanoFocus offers automated solutions which can measure every position of the component automatically. Measurement results are available after a few seconds.

Products: µsurf custom, µsoft analysis

 


Camshafts

Camshafts have typical grinding structures. The roughness according to DIN EN ISO is determined on the basis of a profile section for quality assurance. Evidence of wear and the directional dependence of roughness can also be determined by a 3D measurement.

Products: µsurf explorer, µsurf custom, µsoft analysis


Connection rods

In the laser structuring process, carves and bulking can be measured and evaluated during production. The measurement system automatically moves to freely definable measurement positions while the sample rotates. Once all positions are measured the surface data is evaluated automatically at the hands of profile cuts and the results are protocolled. With the µsurf-technology non-destructive measurement results can be obtained during production.

Products: µsurf custom, µsoft analysis


Engine cylinder walls

The surface topography of cylinder bore surfaces is captured by the µsurf cylinder down to the nanometer range. Honing structures, exposure depths, standard roughness values and the surface roughness can be analyzed with the help of measurement data. This yields qualitative and quantitative information on the wear and defects on the cylinder wall.
Read more about measurements of engine cylinder walls.

Products: µsurf cylinder, µsoft analysis


Benefits at a glance

  • Traceable measurement results
  • Non-destructive measurements
  • Special solutions for different applications in the automotvie industry
  • Measurements on transparent and polishes surfaces
  • 99,9% correlation to tactile measurement results
  • Roughness measurements conform to DIN EN ISO

Contact us online

Call-back service                
System demonstration 
Free test measurement 

Request information

Price quote

 

 

Your contact
Domenique Weiner
Phone:  +49 208 62000-78
Fax:  +49 208 62000-99

Forgot your password?

Please enter your username or email address. Instructions for resetting the password will be immediately emailed to you.

Return to login form